Dental Model Resin for Third-Party Printers
Key Features
RF-ZJ-01 is RayForm’s dental model resin for third-party printers, supplied in five versions, each with its own TDS. The Asiga version is for Asiga printers and the Formlabs version for Form 4; the alcohol-wash, DM12 and HP versions list settings for LCD printers from Phrozen, Elegoo, Anycubic, Creality and PioNext. All five list LCD and DLP processing, a gray appearance and dental models as the application. Choose the version that matches your printer and cleaning method, then validate it on your equipment.
Compare the Five Versions
Typical values from each version’s TDS. A dash means the TDS does not list the value.
| Property | Unit | Alcohol-wash | Asiga | DM12 | Formlabs | HP |
|---|---|---|---|---|---|---|
| Density | g/cm³ | 1.05–1.15 | 1.05–1.15 | 1.10–1.15 | 1.11–1.15 | 1.05–1.15 |
| Viscosity | mPa·s | 350 | 380 | 360 | 1000–1200 | 1100 |
| Hardness | Shore D | 83–86 | 80–85 | 83–87 | 82–85 | 83–87 |
| Tensile Strength | MPa | 51 | 48–70 | 74 | 60 | 62.4 |
| Elongation at Break | % | 12 | 30 | 5 | 10–15 | 17.2 |
| Flexural Strength | MPa | 56 | 80 | 89 | 90–100 | 69.6 |
| Flexural Modulus | MPa | 1430 | 1100 | 1950 | 2700 | 1600 |
| HDT @ 0.45 MPa | °C | — | — | 70 | 70 | 66.4 |
| Color | — | Gray | Gray | Grey | Gray | Gray |
| TDS | V1.0b | V1.0a | V1.0a | V1.0a | V1.0a |
Versions and TDS Downloads
- 1
RF-ZJ-01 (alcohol-wash, low cost) — Low-odor, low-viscosity model resin that prints quickly and is easy to clean; it shows fine detail and has a degree of toughness. Download TDS V1.0b (PDF)
- 2
RF-ZJ-01 for Asiga printers — Model resin for printing on Asiga equipment, with low shrinkage and high toughness; its low viscosity makes it easy to clean and gives detailed prints. Download TDS V1.0a (PDF)
- 3
RF-ZJ-01 DM12 — Versatile model resin for 385/405 nm LCD and DLP printers, with a wide process window, low curing shrinkage and minimal warpage. Download TDS V1.0a (PDF)
- 4
RF-ZJ-01 for Formlabs Form 4 — Model resin that the TDS describes as suitable for Form 4, with 200 micron settings for the fastest prints or 100 micron settings for more detailed models. Download TDS V1.0a (PDF)
- 5
RF-ZJ-01 HP — Model resin with fast forming, high precision and high surface hardness; the TDS reports that precision remained good after more than half a month of storage. Download TDS V1.0a (PDF)
Printing Parameters
Representative machine parameters listed in each version’s TDS. Use them as starting points and validate them for your printer. The Formlabs version names Form 4 but lists no values for it. The printer parameter library also has a “Model resin” profile; ask technical support which RF-ZJ-01 version it matches.
| Printer | Exposure (s) | Base Exp. (s) | Base Layers | Lift Height (mm) | Lift Speed (mm/min) | Retract Speed (mm/min) |
|---|---|---|---|---|---|---|
| RF-ZJ-01 (alcohol-wash, low cost) · TDS V1.0b | ||||||
| Phrozen Sonic Mini 8K S | 3 | 40 | 3 | 4+3 | 60+120 | 180+60 |
| Creality Halot-MAGE Pro | 1 | 15 | 3 | 6+2 | 120+180 | 240+180 |
| Elegoo Saturn 4 Ultra | 1.8 | 25 | 3 | Default standard parameters of the device | ||
| Anycubic Mono 4 Ultra | 2.4 | 30 | 3 | 4+4 | 120+180 | 180+120 |
| Elegoo Saturn 3 Ultra | 2.3 | 30 | 3 | 4+4 | 120+180 | 180+120 |
| Anycubic M7 Pro | 1.6 | 25 | 3 | 4+4 | 120+180 | 180+120 |
| PioNext D158 | 1.5 | 20 | 3 | 8 | 3 mm/s | 4 mm/s |
| RF-ZJ-01 for Asiga printers · TDS V1.0a | ||||||
| Phrozen Sonic Mini 8K S | 10 | 15 | 3 | 12 | 120 | 120 |
| Creality Halot Mega Pro 8K | 2.5 | 17 | 3 | 12 | 120 | 120 |
| Asiga Max (8 mW/cm²) | 2.5 | 12 | 3 | 10 | 120 | 120 |
| RF-ZJ-01 DM12 · TDS V1.0a | ||||||
| Phrozen Sonic Mini 8K S | 6 | 45 | 3 | 8 | 120 | 120 |
| Anycubic Photon Mono 2 | 5 | 30 | 3 | 8 | 120 | 120 |
| Elegoo Saturn 4 Ultra | 4 | 25 | 3 | 8 | 120 | 120 |
| RF-ZJ-01 for Formlabs Form 4 · TDS V1.0a | ||||||
| Phrozen Sonic Mini 8K S | 5 | 6 | 3 | 6 | 120 | 120 |
| Anycubic Photon Mono 2 | 5 | 15 | 3 | 6 | 120 | 120 |
| Anycubic Photon Mono | 5 | 12 | 3 | 6 | 120 | 120 |
| Elegoo Saturn 4 Ultra | 5 | 20 | 3 | 6 | 120 | 120 |
| RF-ZJ-01 HP · TDS V1.0a | ||||||
| Phrozen Sonic Mini 8K S | 2.5 | 9 | 3 | 8 | 120 | 120 |
| Anycubic Photon Mono 2 | 2 | 15 | 3 | 8 | 120 | 120 |
| Anycubic Photon Mono | 2 | 12 | 3 | 8 | 120 | 120 |
| Elegoo Saturn 4 Ultra | 2 | 20 | 3 | 8 | 120 | 120 |
Post-Processing & Storage
- 1
Wash – Alcohol-wash version: clean in an ultrasonic or rotary cleaner with alcohol or isopropyl alcohol. Asiga, DM12, Formlabs and HP versions: rinse residual resin with water, then clean with water or isopropyl alcohol in an ultrasonic cleaner. Avoid high-frequency shock or forceful scrubbing to protect surface details.
- 2
Dry – Thoroughly blow the model dry with a hair dryer or similar tool.
- 3
Remove Supports – Remove supports before post-curing. Removing them after post-cure can damage the contact surface at support points.
- 4
Post-Cure – Where certain toughness is required, UV cure for 5 minutes. Keep printed parts in a cool, dry place.
Storage
Store below 25°C in a cool place away from direct sunlight. Ordinary visible light may cause the resin to polymerize and gel.
Safety
Eyes: Flush with clean water for at least 20 minutes and seek medical attention immediately. Skin: Remove contaminated clothing and wash thoroughly with soap and water. Not approved for food, drink, or medical application on the human body. See MSDS for details.
Compatible Third-Party Printers
Third-party printers named in at least one RF-ZJ-01 TDS. Each version lists its own printers; check the parameter table above for the version you plan to use.
Asiga, Formlabs, Form 4 and other printer names are trademarks of their respective owners.
Dental Model Applications
All five TDS versions list dental models as the application. Validate dimensional accuracy, cleaning and post-curing on your own printer before production.

Supply & Technical Support
Contact RayForm for current pack options, sample availability, quotations, technical documents, and printer starting profiles for the RF-ZJ-01 version you plan to use.
Current Supply Options
Pack sizes and order formats may vary by market. Request current availability and a quotation for your project.
Samples & Parameters
Request samples, technical documentation, and printer-specific starting parameters for workflow validation.
Frequently Asked Questions
- QWhat is RF-ZJ-01 used for?
RF-ZJ-01 is a gray dental model resin for third-party printers. All five TDS versions list dental models as the application and LCD/DLP processing; the Asiga version is for Asiga printers and the Formlabs version for Form 4. - QWhich RF-ZJ-01 version should a lab choose?
Match the version to the printer and cleaning method: the Asiga version for Asiga printers, the Formlabs version for Form 4, the alcohol-wash version for alcohol or isopropyl alcohol cleaning, and the DM12 or HP version for the LCD/DLP printers listed in their TDS. Validate the chosen version on your own equipment before production. - QHow do the five versions differ in material data?
In the TDS typical values, flexural modulus ranges from 1100 MPa (Asiga) to 2700 MPa (Formlabs) and viscosity from 350 mPa·s (alcohol-wash) to 1000–1200 mPa·s (Formlabs). The DM12, Formlabs and HP versions also report HDT at 0.45 MPa of 70, 70 and 66.4 °C. - QWhich third-party printers can use RF-ZJ-01?
The RF-ZJ-01 TDS set lists settings for the Asiga Max (Asiga version) and for LCD printers: Phrozen Sonic Mini 8K S, Elegoo Saturn 3 Ultra and Saturn 4 Ultra, Anycubic Photon Mono, Photon Mono 2, Mono 4 Ultra and M7 Pro, Creality Halot-MAGE Pro and Halot Mega Pro 8K, and PioNext D158. The Formlabs version names Form 4 without listing values for it, so ask RayForm technical support for Form 4 settings. Each version lists its own printers; validate the chosen version on your printer. - QHow should printed models be cleaned?
The alcohol-wash version is cleaned in an ultrasonic or rotary cleaner with alcohol or isopropyl alcohol. For the Asiga, DM12, Formlabs and HP versions, rinse residual resin with water, then clean with water or isopropyl alcohol in an ultrasonic cleaner. Dry the model and remove supports before post-curing. - QIs RF-ZJ-01 approved for direct use on the human body?
No. Each RF-ZJ-01 TDS states that the resin is not approved for food, drink, or medical application on the human body. It is a dental model material. - QHow do I request a quote or samples?
Choose Get a Quote and include the RF-ZJ-01 version, your printer model, the required quantity and the target market.
Evaluate RF-ZJ-01 for your dental model workflow
Tell RayForm your printer, material application and expected volume. Request a sample, TDS, starting parameters and a current supply quotation.
Explore More Materials
Compare RayForm resins by printed component, cleaning process and material data to select a laboratory production workflow.